Usage instructions:
Operating instructions: The iron may give off some smoke and emit an odour when you first use. This will cease after a short while. It is safe and will not harm the performance of the iron. Filling with water: Remove the mains plug from the wall socket before filling the iron. Set the steam button to position "O" or " " and open the water inlet cover. Please fill your iron with normal tap water before using for the first time. Use the water beaker attached to fill clean tap water into water tank until "MAX" filling level. For refilling, you can also use tap water. However, if the water is very hard it is advisable to use distilled water. Replace water inlet cover and dry the spilt water around the enclosure of the appliance. Do not fill the tank beyond the MAX indication. Do not put perfume, vinegar, starch, descaling agents, ironing additives, chemically descaled water or other chemicals in the water tank. Setting the temperature: Fabric temperature control: Nylon/acrylic/acetate. Silk/rayon/polyester. Wool/cotton. Linen max. Stand the iron on its heel and plug the power cord into wall socket. Turn the iron temperature control knob until you get the desired fabric/temperature setting. We recommend using the above table as a guide. The temperature pilot light will light up, indicating that the soleplate is heating up. When the pilot light goes out, the required temperature has been reached. The temperature pilot light will go on from time to time during ironing. Dry ironing: For dry ironing, turn the steam control knob to "O" or " ". This will cut off the steam flow if water is in the water tank. Turn the temperature control knob to select the desired fabric/temperature setting. The indicator pilot light will light, put the iron on a smooth and stable place, vertically. After the indicator pilot light goes out, you can begin to iron. Spraying: Ensure there is enough water in the water tank. Press the spray button to produce a fine spray of water nozzle and continue ironing. Note: do not spray silk fabric. Steam-ironing: As indicated on the temperature control and the table on the iron, steam-ironing is only possible at higher ironing temperatures (between ** to "MAX"). Ensure that there is enough water in the water tank. Stand the iron on its end and insert the main plug into the wall socket. Set the temperature control knob at the required position within the steam area. After the indicator pilot light has gone out and has come on again, you may start ironing. Turn the steam control knob to the required position. Burst of steam: Ensure that there is enough water in the water tank. When the temperature control knob is set to steam setting (between '**' to "MAX") strong steam can be used. Press the burst steam button, the soleplate will spray out a strong burst of steam. Attention: Only use the steam push button when the steam iron has reached the steam or maximum temperature. Do not press this burst steam button more than 3 times at once. For optimal steam output, leave an interval of at least four seconds between pressing the burst steam button. The burst steam feature can be used with dry or steam ironing as desired. Note: never direct the steam towards people. Burns or serious injury may occur. Vertical shot of steam: When the temperature control knob is set to a steam setting (between '**' to "MAX") vertical steam can be used. Simply hold the iron vertically, positioned in front with a slight distance from the item to be steamed, and press the burst steam button. This is especially useful for getting creases out of hanging clothes, curtains, wall hangings, ect. Automatic anti-calc function: Your iron contains an anti-calc cartridge to reduce scale deposits. This considerably prolongs the operation life of your iron. The anti-calc cartridge is an integral part of the water tank and dose not needs to be replaced. Automatic anti-drip function: Your iron has an anti-drip function. The iron automatically stops generating steam when the temperature is too low to prevent water from dripping out of the soleplate. Self-clean function: Use the self-clean function once every two weeks. If the water in your area is very hard, the self clean function should be used more frequently. Make sure the iron is unplugged. Set the steam control knob to OFF position. Fill the water tank to the maximum level. Put the plug in the wall socket. Select the maximum ironing temperature. Unplug the iron when the temperature pilot light has gone out. Hold the iron over the sink, press and hold the self-clean button and gently shake the iron to and fro. Release the self-clean button after 5-10 seconds. Repeat the self-clean process if the iron still contains a lot of impurities. Note: steam and boiling water will come out of the soleplate, impurities and flakes (if there are any) will be flushed out. Do not push and hold the self clean button while ironing. Auto-shut-off function: The auto-shut-off function automatically switches off the iron if it has not been moved for a while. The auto-off pilot light starts flashing (or the buzzer will start beeping) to indicate that the iron has been switched off by the auto-shut-off function. To let the iron heat up again: Pick up the iron or move it slightly. The auto-off pilot light stop flashing (or the buzzer will stop beeping). If the temperature of the soleplate has dropped below the set ironing temperature, the temperature pilot light will turn on. If the temperature pilot light turns on after you have moved the iron, wait until it goes out before you start ironing. If the temperature pilot light does not go on after you move the iron, the soleplate still has the right temperature and the iron is ready for use. When auto-shut-off function happens you may hear a sound. Care and cleaning: Before cleaning, set the steam control knob to the "O" or unplug the iron from wall socket, and allow the appliance to completely cool down, and then clean with a damp cloth, do not immerse the unit into water or other liquids. Regularly rinse the water tank with water, empty the water tank after cleaning. Ironing clothes using a high temperature, which is not recommended on the garment table, will cause burns to your clothes. Iron an old cloth to remove residue left on the soleplate. If you use spray starch, wipe the soleplate occasionally with a soft, damp cloth to prevent the build-up of deposits. After use, set the steam control knob to the "O" or disconnect the unit from main socket, empty remaining water from water tank and then store the iron after it has completely cooled down. Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/or damage its surface.

Warnings:
Appliance will remain hot for a period of time after use. Do not leave product unattended while in use. Due to continued product improvement, the product illustrated on this carton may vary slightly from the actual product

Information not available.