How to use:
Using Your Sonic Lite Toothbrush If you’re using your Sonic Lite toothbrush for the first time, it’s normal to feel more vibration than if you were using a manual or battery-powered toothbrush. Some people notice a slight tickling or buzzing sensation – this will pass in time. We recommend using the Sensitive mode for the first 1-2 weeks, then trying the Clean mode once you’ve become accustomed to the sensation. Your Sonic Lite toothbrush has two modes: Sensitive and Clean. The Sensitive mode is good for people with sensitive teeth or gums, while the Clean mode is perfect for powerful everyday cleaning. Each mode can be selected by pressing the power button multiple times until you reach your desired mode. Your Sonic Lite remembers the last mode you used, so next time you use it, all you need to do is press the power button and you’re good to go. It’s common for first-time users to apply too much pressure. The benefit of an electric toothbrush is that it does the brushing for you, so you only need to apply gentle pressure. Please follow the instructions below for the best brushing experience. This toothbrush is safe to use on braces, dental restorations (fillings, crowns, bridges, implants), and cosmetic dental work (veneers, composite bonding), as long the dental work is properly adhered and not compromised. Please ask your dentist for advice if you’re unsure in any way. Brushing instructions: 1. Wet the bristles and apply a pea-sized amount of toothpaste. 2. Place the toothbrush bristles at a 45-degree angle to the teeth, pressing just enough to make the bristles reach the gum line. 3. Press the power/mode button to switch on the toothbrush and select your desired mode. 4. Remember not to press too hard when brushing, let the vibrating bristles do the work of clearing away plaque and food debris – no need to scrub as you might with a manual toothbrush. 5. Guide the bristles across and between your teeth, using small back and forth motions. 6. To ensure you thoroughly brush all surfaces of your teeth, split your mouth into four quadrants: top teeth outer surfaces, top teeth inner surfaces, bottom teeth outer surfaces, bottom teeth inner surfaces. Use the inbuilt Quad-Pacer to guide you between each of the quadrants – every 30 seconds the vibrations will pause briefly to let you know it’s time to move onto the next quadrant. 7. After 2 minutes the toothbrush will automatically switch off, letting you know that you’ve brushed your teeth for the dentist recommended time. Of course, you can switch the toothbrush back on if you’d like to brush for longer. 8. If at any time before the end of a 2-minute cycle you want to turn the toothbrush off, simply press the power/mode button. 9. Once you’re done with brushing, spit out any excess toothpaste, but do not rinse your mouth with water. This allows the ingredients of the toothpaste to better protect your teeth. 10. Thoroughly rinse the bristles, brush head and handle, ensuring you wash away any toothpaste residue. Charging Your Sonic Lite Toothbrush 1. When the rechargeable battery is low, the battery indicator will flash red. 2. Pop open the charging cover on the bottom of the toothbrush. To help open the charging cover, it has a small cut-out near the “ORDO” logo on the back of the toothbrush. 3. Ensure the entire toothbrush is fully dry, paying particular attention to the bristles and the area around the charging cover and USB-C charging input. 4. Using the included USB cable, connect the USB-A connector to a power source, then connect the USB-C connector to the USB-C charging input on the toothbrush. 5. The battery indicator will light up red to show the toothbrush is being charged. 6. Allow the toothbrush to charge for 4 hours or until the charging light shows green. 7. Disconnect the USB cable from the toothbrush and switch off the power source. 8. Securely and fully close the charging

Warnings:
Not for use by children under 8 years old.

Information not available.